FreeBSD 7.4-RELEASE Hardware Notes
Prev Next

2 Supported Processors and System Boards

This section provides some architecture-specific information about the specific processors and systems that are supported by each architecture.

2.1 amd64

Since mid-2003 FreeBSD/amd64 has supported the AMD64 (“Hammer”) and Intel® EM64T architecture, and is now one of the Tier-1 platforms (fully supported architecture), which are expected to be Production Quality with respects to all aspects of the FreeBSD operating system, including installation and development environments.

Note that there are two names for this architecture, AMD64 (AMD) and Intel EM64T (Extended Memory 64-bit Technology). 64-bit mode of the two architectures are almost compatible with each other, and FreeBSD/amd64 should support them both.

As of this writing, the following processors are supported:

Intel EM64T is an extended version of IA-32 (x86) and different from Intel IA-64 (Itanium) architecture, which FreeBSD/ia64 supports. Some Intel's old documentation refers to Intel EM64T as “64-bit extension technology” or “IA-32e”.

The largest tested memory configuration to date is 32GB. SMP support has been recently completed and is reasonably robust.

In many respects, FreeBSD/amd64 is similar to FreeBSD/i386, in terms of drivers supported. There may be some issues with 64-bit cleanliness in some (particularly older) drivers. Generally, drivers that already function correctly on other 64-bit platforms should work.

FreeBSD/amd64 is a very young platform on FreeBSD. While the core FreeBSD kernel and base system components are generally fairly robust, there are likely to still be rough edges, particularly with third party packages.

2.2 i386

FreeBSD/i386 runs on a wide variety of “IBM PC compatible” machines. Due to the wide range of hardware available for this architecture, it is impossible to exhaustively list all combinations of equipment supported by FreeBSD. Nevertheless, some general guidelines are presented here.

Almost all i386™-compatible processors with a floating point unit are supported. All Intel processors beginning with the 80486 are supported, including the 80486, Pentium, Pentium Pro, Pentium II, Pentium III, Pentium 4, and variants thereof, such as the Xeon and Celeron® processors. All i386-compatible AMD processors are also supported, including the Am486®, Am5x86®, K5, AMD-K6® (and variants), AMD Athlon (including Athlon-MP, Athlon-XP, Athlon-4, and Athlon Thunderbird), and AMD Duron™ processors. The AMD Élan SC520 embedded processor is supported. The Transmeta Crusoe is recognized and supported, as are i386-compatible processors from Cyrix and NexGen.

There is a wide variety of motherboards available for this architecture. Motherboards using the ISA, VLB, EISA, AGP, and PCI expansion busses are well-supported. There is some limited support for the MCA (“MicroChannel”) expansion bus used in the IBM PS/2 line of PCs.

Symmetric multi-processor (SMP) systems are generally supported by FreeBSD, although in some cases, BIOS or motherboard bugs may generate some problems. Perusal of the archives of the FreeBSD symmetric multiprocessing mailing list may yield some clues.

FreeBSD will take advantage of HyperThreading (HTT) support on Intel CPUs that support this feature. A kernel with the options SMP feature enabled will automatically detect the additional logical processors. The default FreeBSD scheduler treats the logical processors the same as additional physical processors; in other words, no attempt is made to optimize scheduling decisions given the shared resources between logical processors within the same CPU. Because this naive scheduling can result in suboptimal performance, under certain circumstances it may be useful to disable the logical processors with the the machdep.hlt_logical_cpus sysctl variable. It is also possible to halt any CPU in the idle loop with the machdep.hlt_cpus sysctl variable. The smp(4) manual page has more details.

FreeBSD will take advantage of Physical Address Extensions (PAE) support on CPUs that support this feature. A kernel with the PAE feature enabled will detect memory above 4 gigabytes and allow it to be used by the system. This feature places constraints on the device drivers and other features of FreeBSD which may be used; consult the pae(4) manpage for more details.

FreeBSD will generally run on i386-based laptops, albeit with varying levels of support for certain hardware features such as sound, graphics, power management, and PCCARD expansion slots. These features tend to vary in idiosyncratic ways between machines, and frequently require special-case support in FreeBSD to work around hardware bugs or other oddities. When in doubt, a search of the archives of the FreeBSD laptop computer mailing list may be useful.

Most modern laptops (as well as many desktops) use the Advanced Configuration and Power Management (ACPI) standard. FreeBSD supports ACPI via the ACPI Component Architecture reference implementation from Intel, as described in the acpi(4) manual page. The use of ACPI causes instabilities on some machines and it may be necessary to disable the ACPI driver, which is normally loaded via a kernel module. This may be accomplished by adding the following line to /boot/device.hints:

hint.acpi.0.disabled="1"

Users debugging ACPI-related problems may find it useful to disable portions of the ACPI functionality. The acpi(4) manual page has more information on how to do this via loader tunables.

ACPI depends on a Differentiated System Descriptor Table (DSDT) provided by each machine's BIOS. Some machines have bad or incomplete DSDTs, which prevents ACPI from functioning correctly. Replacement DSDTs for some machines can be found at the DSDT section of the ACPI4Linux project Web site. FreeBSD can use these DSDTs to override the DSDT provided by the BIOS; see the acpi(4) manual page for more information.

2.3 ia64

Currently supported processors are the Itanium® and the Itanium 2.

Supported chipsets include:

Both Uniprocessor (UP) and Symmetric Multi-processor (SMP) configurations are supported.

Most devices that can be found in or are compatible with ia64 machines are fully supported. The notable exception is the VGA console. The FreeBSD support for VGA consoles is at this time too much based on PC hardware and not all ia64 machines have chipsets that provide sufficient PC legacy support. As such syscons(4) can not be enabled and the use of a serial console is required.

2.4 pc98

NEC PC-9801/9821 series with almost all i386-compatible processors, including 80486, Pentium, Pentium Pro, Pentium II, and variants. All i386-compatible processors by AMD, Cyrix, IBM, and IDT are also supported.

NEC FC-9801/9821 series, and NEC SV-98 series (both of them are compatible with PC-9801/9821 series) should be supported.

EPSON PC-386/486/586 series, which are compatible with NEC PC-9801 series are supported.

High-resolution mode is not supported. NEC PC-98XA/XL/RL/XL^2, and NEC PC-H98 series are supported in normal (PC-9801 compatible) mode only.

Although there are some multi-processor systems (such as Rs20/B20), SMP-related features of FreeBSD are not supported yet.

PC-9801/9821 standard bus (called C-Bus), PC-9801NOTE expansion bus (110pin), and PCI bus are supported. New Extend Standard Architecture (NESA) bus (used in PC-H98, SV-H98, and FC-H98 series) is not supported.

2.5 powerpc

The information for this paragraph has yet to be compiled.

2.6 sparc64

This section describes the systems currently known to be supported by FreeBSD on the Fujitsu SPARC64® and Sun UltraSPARC® platforms. For background information on the various hardware designs see the Sun System Handbook.

SMP is supported on all systems with more than 1 processor.

When using the GENERIC kernel, FreeBSD/sparc64 systems not equipped with a framebuffer supported by the creator(4) (Sun Creator, Sun Creator3D and Sun Elite3D) or machfb(4) (Sun PGX and Sun PGX64 as well as the ATI Mach64 chips found onboard in for example Sun Blade™ 100, Sun Blade 150, Sun Ultra™ 5 and Sun Ultra 10) driver must use the serial console.

If you have a system that is not listed here, it may not have been tested with FreeBSD 7.4-RELEASE. We encourage you to try it and send a note to the FreeBSD SPARC porting mailing list with your results, including which devices work and which do not.

The following systems are fully supported by FreeBSD:

The following systems are partially supported by FreeBSD. In particular the fibre channel controllers in SBus-based systems are not supported. However, it is possible to use these with a SCSI controller supported by the esp(4) driver (Sun ESP SCSI, Sun FAS Fast-SCSI and Sun FAS366 Fast-Wide SCSI controllers).

Starting with 7.2-RELEASE, sparc64 systems based on Sun UltraSPARC III and beyond are also supported by FreeBSD, which includes the following known working systems:

The following Sun UltraSPARC systems are not tested but believed to be also supported by FreeBSD:

Starting with 7.4-RELEASE and 8.1-RELEASE, sparc64 systems based on Fujitsu SPARC64 V are also supported by FreeBSD, which includes the following known working systems:

The following Fujitsu PRIMEPOWER systems are not tested but believed to be also supported by FreeBSD:

Prev Home Next
FreeBSD 7.4-RELEASE Hardware Notes   Supported Devices

This file, and other release-related documents, can be downloaded from ftp://ftp.FreeBSD.org/.

For questions about FreeBSD, read the documentation before contacting <[email protected]>.

All users of FreeBSD 7.4-STABLE should subscribe to the <[email protected]> mailing list.

For questions about this documentation, e-mail <[email protected]>.